山西專業分析儀

氧氮?dú)浞治鰞x

氧氮?dú)浞治鰞x是一種用于材料科學領域的儀器，于2016年03月09日啟用。

技術指標

測量范圍： ON 低氧0.0－300ppm OH 低氧0.0－300ppm 高氧0.0－2% 高氧0.0－2% 低氮0.0―300ppm 低氫0.0－50ppm 高氮0.0－2% 高氫0.0－1000ppm 靈敏度： 氧0.01ppm；氮0.1ppm；氫0.01ppm。

主要功能

該儀器配置有16位微處理器和兩個**的分別檢測高氧和低氧的 紅外檢測池。氮和氫通過雙重范圍的熱導檢測池測量。分析過程中可自動實現從 低范圍到高范圍的切換。樣品在高功率脈沖爐的石墨坩堝中加熱可達3000℃以上 高溫，脈沖爐采用循環水冷卻。該儀器具有靈敏度高、性能好、測量范圍寬和分 析結果準確可靠等優點。ONH-2000氧氮?dú)浞治鰞x是為快速、準確測定銅、鋼、鑄 鐵、合金、鈦、鎳、鉬、鋯、陶瓷和其它無機材料中氧、氮、氫的含量而專門設計 制造的。 雙直流風扇保證持續冷卻，不受電壓波動的影響。山西專業分析儀

Instrument calibration/drift correction

f. Clean the upper and lower electrode manually, or, if applicable, remove the crucible and press the analyze button to clean with the automatic cleaner.

g. Firmly place a graphite crucible on the lower electrode tip.

h. Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and end automatically.

i. Repeat steps 3b through 3h a minimum of three times for each calibration/drift standard used.

. Calibrate/drift following the procedure outlined in the operator's instruction manual.

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Calibrate/drift following the procedure outlined in the operator's instruction manual.

Login Sample with the appropriate number of reps.

Weigh approximately *** grams of appropriately prepared sample into a *** Nickel Capsule, enter mass and sample identification into appropriate rep fields. If applicable, place the nickel capsule in the

appropriate autoloader position.

Repeat steps 3c through 3i for sample analysis.

氧氮?dú)浞治鰞x的操作過程

氧氮?dú)浞治鰞x可根據的用戶的要求定制。該分析儀配備兩個不同靈敏度的探測器，在更多的應用中保證了準確度。

操作簡單而且安全。在樣品稱重以后，樣品的重量數據通過電子界面?zhèn)鲗?dǎo)至相連的電腦中，也可以在軟件界面中手動輸入樣品的重量。

樣品被放置在水平放置的爐子中的低溫區域。分析開始以后，爐子開始向上轉動，然后樣品逐漸落入加熱區。通過添加載體氣體氮?dú)?，氫氣被擴散出來并且隨載體被傳導至一個高靈敏度的熱傳導測量池。

通常一次測量的時間在3到15分鐘之間。在分析的過程中設備可以顯示測試信號和設備的參數，從信號的評估到結果在界面上的顯示全部自動完成；而測量數據則被傳導至LIMS（實驗室信息管理系統）中。無需過多的保養和維護，而除塵器和凈化管的維護工作也方便。

Method Selection

Two methods are described in this application note; either method can be used to analyze iron, steel, nickel-, and cobalt-base alloys. The Precision Method is recommended for general use and will provide the best precision and accuracy throughout the typical O, N, and H concentrations found in this group of metals; approximate cycle time is 3.5 minutes. The Fast Track method can be used where speed of analysis is a critical component; for example, when molten metal is being sampled and results are required in the shortest possible time. This method will produce suitable results for most samples; approximate cycle time is 2.25 minutes. As noted above, sampling and sample preparation are key elements to accurate O, N, and Hdetermination as well. It is up to the user to determine which method best meets their needs.

**的動態流量補償（DFC）保證熱導池氣體流量、壓力恒定。安徽美國LECO氧氮?dú)浞治鰞x采購

裝有自動旁路閥的可快速拆裝氧水捕集裝置。山西專業分析儀

力可ONH836氧氮?dú)浞治鰞x

特征

穩固的爐頭試樣加載結構

試樣加載過程中完全密閉，消除大氣的中可能帶來的雜質的污染；

簡化日常分析所需的爐頭進樣部分機械維護工作。

可選的自動功能

上下電極自動清掃裝置；

20位試樣及坩堝自動進樣裝置。

附加功能及優點

可選六軸可旋轉觸摸屏幕，增強了操作的工效和直觀性；

可選具有壓力補償和溫度控制性能的標氣檢測氣路；

新型氣路管道減少氣路連接閥，使得漏氣，斷路故障更少；

配置SmartLine Remote遠程診斷功能。

山西專業分析儀