浙江LECO氧氮氫分析儀采購

736 Series: Oxygen/Nitrogen by Inert Gas Fusion

The 736 family of Elemental Analyzers is designed for routine measurement of oxygen and nitrogen content of

inorganic materials, ferrous and nonferrous alloys, andrefractory materials using the inert gas fusion technique.

These instruments feature our Cornerstone brand ® software, a custom interface designed specifically for

touch-screen operation. Developed by combining longterm research with customer feedback, this easy-to-use

software gives you complete access to instrument control, analysis settings, diagnostics, reporting, and more—without sacrificing valuable bench space.

雙直流風扇保證持續冷卻，不受電壓波動的影響。浙江LECO氧氮氫分析儀采購

氧氮氫分析儀的優點

采用惰氣熔融技術，同時測定氧、氮和氫元素含量

新設計封閉氣路系統，優化氣路循環，使氧氮氫測量更準確

可采用更廉價的氬氣作為載氣

催化爐溫度可調，使氧的測量更加準確

氣路系統都采用電磁閥控制，新增分段式漏氣檢測

水冷樣品加樣端口，有效隔絕雜質氣體侵入

儀器配置和氧、氮、氫測量范圍可靈活選擇

新設計的高靈敏度紅外檢測池和熱導池，有極低的檢出限

分析時間短

脈沖爐功率高達8.5kw，溫度3000℃

顆粒狀樣品無需膠囊包裹，使用經濟實惠

化學試劑及管路隱藏在門后（可移除）

強大的分析軟件（支持數據和應用報告導出、增加評論區及其他更多功能）。

單點和多點校正（線性回歸）

可采用自來水、冷卻循環水機或交換機冷卻

新設計的產品可用于各類生產控制和實驗室。

Method Selection

Two methods are described in this application note; either method can be used to analyze iron, steel, nickel-, and cobalt-base alloys. The Precision Method is recommended for general use and will provide the best precision and accuracy throughout the typical O, N, and H concentrations found in this group of metals; approximate cycle time is 3.5 minutes. The Fast Track method can be used where speed of analysis is a critical component; for example, when molten metal is being sampled and results are required in the shortest possible time. This method will produce suitable results for most samples; approximate cycle time is 2.25 minutes. As noted above, sampling and sample preparation are key elements to accurate O, N, and Hdetermination as well. It is up to the user to determine which method best meets their needs.

氧氮氫分析儀的使用注意事項：

1 、氧氮氫分析儀在初次啟用前，應該對連接點、焊點、閥門等進行檢漏，以確?？諝庵械难醪粫礉B進入管道及儀器內部，造成測量數值偏高。

2、再次使用儀器前，要進行管道系統凈化，將漏入的空氣除干凈，同時確保連接取樣管路時沒有漏入空氣。

3、樣氣中氧含量的變化會受管道材質及表面粗糙度影響，因此一般連接管路選用銅管或拋光過的不銹鋼管，而不用塑料管、橡膠管等。

4、微量元素分析時，要避免各種管件、閥門、表頭等死角對樣氣造成污染，因此必須盡可能的簡化氣路系統，連接件死角要小，以防止溶解氧逸出造成污染，使用水封、油封及臘封等設備，才能較好的確保數據的。

長壽命的紅外發射光源和無漂移的電路設計保證紅外檢測池的長期穩定性。

Instrument calibration/drift correction

f. Clean the upper and lower electrode manually, or, if applicable, remove the crucible and press the analyze button to clean with the automatic cleaner.

g. Firmly place a graphite crucible on the lower electrode tip.

h. Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and end automatically.

i. Repeat steps 3b through 3h a minimum of three times for each calibration/drift standard used.

. Calibrate/drift following the procedure outlined in the operator's instruction manual.

全自動分析系統、打印機、天平、遠程診斷。浙江LECO氧氮氫分析儀采購

Sample Preparation

Sampling and sample preparation is an important issue because traditional methods used to obtain samples for oxygen and nitrogen determination are different from those recommended for hydrogen, especially when sampling molten metal. The main difference in steel sampling procedures for oxygen/nitrogen and hydrogen is due to the mobilityof hydrogen. Special precautions must be used when sampling for hydrogen. From molten steel and iron, a sample must be quickly quenched in cold water and chilled in a refrigerant such as liquefied nitrogen or a mixture of acetone and solid carbon dioxide in order to reduce losses of hydrogen from diffusion. Losses of oxygen and nitrogen from diffusion are not a problem. A sample that is taken for hydrogen and

chilled in a refrigerant can also be used for oxygen and nitrogen determination. However, a sample that is typically taken for oxygen and/or nitrogen determination is not suitable for hydrogen determination due to hydrogen loss (diffusion). Surface contamination must be removed by filing or light grinding, using care not to overheat the sample.

浙江LECO氧氮氫分析儀采購